Ductile Iron Fire Protection Coupling
Made to Awwa C606 and ISO6182, we support OEM on logo and coating, with a 10 year warranty. FOB pricing runs US $6-12 per piece.
Ductile Iron Fire Protection Coupling
Rigid coupling joining fire main sections
The ductile iron rigid grooved coupling serves fire protection and water supply mains. It is a QT450 ductile iron body with sealing gasket; DN50 to DN200. The listed reference records the product type as Grooved Fitting. The listed model reference is XGQT. In service the body has to hold internal pressure and the modest external loads from clips, supports and occasional contact during maintenance, while the outside surface takes whatever corrosion practice the installation applies after the line goes into service. Contractors usually pull the bore, wall and end form from the spool list before the shop cuts the piece, so the batch matches the take-off rather than a mixed stock assortment. The route often turns again within the same block, so adjacent pieces are listed together on the same drawing sheet. The fitting is staged alongside the spool it joins.

Ductile iron body with sealing gasket
How the material behaves under service depends on the medium carried and the environment around the line. The wall section carries internal pressure without permanent deflection, and the body flexes only slightly when bedding or supports settle under a settled line. Where the piece meets the atmosphere, surface condition is checked against the order record before packing, and any end that does not match the recorded bore is set aside rather than shipped with the batch. Over repeated temperature cycling and occasional wetting, the material keeps its dimensional stability, and the joint itself remains the part that needs the closest watching during the first pressure test. Buyers on a scheduled contract usually order several matching pieces in one slot so fabrication does not stop between sections of the same run.
Mismatched OD shows at first fit-up. The welder spots it before the arc strikes.
Grooved ends clamped around the barrel
The listed end form governs how the piece seats against the adjoining pipe. For welded preparations the bevel and outside diameter are matched flush to the mating tube before the joint closes, while threaded and socket-weld options follow the thread or socket profile recorded on the listing. A skewed insertion leaves one side under-sealed and usually shows weeping after the first hydrostatic check, so the crew seats the piece square and checks the joint angle before backfill or support clips go on. The joint has to stay aligned with the centerline pattern on the spool drawing, and the recorded dimension on each end is compared against that drawing before the piece leaves the shop. Where flanges are involved, bolts are pulled in cross sequence so the gasket compresses evenly around the full ring.
Street fire main and water supply runs
These pieces end up on fire protection and water supply mains. Around a station or plant the line routes between racks, decks, pump houses and individual units, and each section calls for the fitting that matches its own spool list. Small branches feed local take-offs while larger mains carry the main flow through open corridors and crossings, and the same body type appears in both sizes across the order record. Field crews stage the pieces along the trench or rack before stringing begins, sorting by nominal size so the right fitting reaches the right joint at the right moment. Local conditions such as cover depth, groundwater level and soil type narrow the size and class choice before the first length is laid in.
On site, the piece is staged alongside the spool it joins, and the crew checks nominal size, wall and end condition before the first connection is made. Supports and clips are placed so the body does not carry an unintended external load, and the joint is left accessible for the first pressure test and any later inspection. Where the run crosses a trench, chamber or rack, the fitting is aligned to the centerline pattern on the drawing rather than pulled straight by hand. Receiving inspection sorts the batch by size against the order reference, and any piece that does not match the recorded bore or end form is set aside instead of being mixed into the installed run. Spare pieces for future maintenance are held in store by bore and wall, separate from the current installation.
Record the bore on the sheet. Match the wall to the duty. Keep spare pieces by size in store.
| Fitting | Rating |
|---|---|
| Pressure rating | Pn16 (16 bar / 232 psi) |
| Model reference | XGQT |
| Product category | Grooved Fitting |
| Intended service | Fire protection and water supply |
| Standard or certification record | Awwa C606, ISO6182 |
| End connection form | Grooved |
| Bore and size range | DN50 to DN200 |
| Body material | QT450 Ductile Iron |
| Listed fitting type | Grooved Coupling |
Pressure rating checked against the line
When the order comes through, nominal size, wall and end condition are recorded on the sheet, and the shop cuts the piece to those dimensions before it moves to surface check and packing. The record lists the standard references Awwa C606, ISO6182; these are the only standards quoted for this piece, and any project specification beyond them should be checked separately. Custom dimensions are prepared to order instead of being pulled from a fixed stock bin, which is why the size band in the listing bracket stays wide across the range. Small lots are accepted, and the usual production timing and pricing bracket appear in the listing record. Each piece in the batch carries the same order reference, which lets receiving inspection sort the pieces by size without opening every crate. Spare pieces for future maintenance are held in the store by bore and wall, separate from the batch installed on the current run.
Surface and end check come before packing. A fresh weld fails inspection most often because grit sat on the bevel.
Hot Tags: Ductile Iron Fire Protection Coupling, China Ductile Iron Fire Protection Coupling manufacturers, carbon steel adapter fittings, carbon steel industrial piping components, carbon steel pipe fitting, carbon steel plug fittings, carbon steel process fittings, Seamless Carbon Steel Elbow
You Might Also Like
Send Inquiry














