Ductile Iron Mechanical Grooved Cross
video

Ductile Iron Mechanical Grooved Cross

QT450 ductile iron grooved mechanical cross for fire protection, silver finish, DN80 to DN200 at 1.6MPa. Most end up branching street fire protection and warehouse sprinkler mains.
We back these with a 10 year warranty and turn out around 3,000,000 pieces a year. FOB pricing runs US $14-22 per piece, minimum order 1 piece.
Send Inquiry
Product Introduction

Ductile Iron Mechanical Grooved Cross

Mechanical crosses on sprinkler mains

This QT450 ductile iron grooved mechanical cross serves fire protection piping, branching street mains and warehouse sprinkler circuits where a four-way mechanical connection is required. The listed range covers DN80 to DN200 at 1.6 MPa, with a grooved connection held by a split housing over a gasket. The nodular iron body carries pressure and joint restraint without permanent sag, and the casting machines cleanly at the groove seats. The listed certification reference reads GB on the source record, and the drawing confirms pressure class and gasket type against the service on that line.

Street-main crews torque the clamp in sequence. Even gasket compression keeps the joint from weeping.

Ductile iron casting and grooved housing

The body is QT450 ductile iron, a casting with nodular graphite that combines cast iron's shape-making ease with steel-like strength and toughness. The wall holds internal pressure and the hoop loads from joint restraint without permanent sag, and the casting machines cleanly at grooves, threads or flange faces. Finish condition follows the listed surface, and any external paint is applied per project practice after installation.

Before the piece leaves the plant, surface condition and dimensions are checked against the listing record, and any burr, casting flash or uneven thread is dressed back to the body profile. Wall thickness and outside diameter are sampled against the listed size range, and the end faces are protected with thread or end caps until the joint is ready to close. On site, crews brush grit from the bore and the sealing face before assembly, because sand or scale left on a thread or gasket seat is the usual reason a fresh connection weeps after the first pressure test. Spare pieces ride along with the next valve or fitting order, held in the maintenance store by line size and end type so the replacement matches the run it serves.

Ductile iron grooved mechanical cross for fire protection sprinkler mains
Mechanical grooved cross staged beside a warehouse sprinkler main.

Diameter, pressure and listed certification

The listed size range reads DN80 to DN200 on the source record. The listed pressure envelope reads 1.6MPa. Listed standards and certification references read GB, copied as they appear on the source listing; the drawing should confirm the applicable grade and test record before fabrication. Listed service on the source record: Fire protection piping.

Dimension selection starts from the flow requirement on the line drawing, then narrows against pressure class, span length and the end form listed for that fitting. Where two sizes sit close on the range, the larger wall and diameter give margin against transient surge and support loads, while the smaller size keeps weight and cost down on branches that carry little flow. The drawing should fix outside diameter, wall thickness and end preparation before the order is cut, so the workshop does not guess at a dimension that falls outside the listed stock range. Spare sets are held in the maintenance store tagged by line size, end form and pressure class, which keeps the replacement matched to the run it serves. On installation, supports and hangers follow the span conditions listed for that pipe. The joint is aligned square before bolts come tight or welds are laid down.

Grooved clamp assembly in the street main

The connection is grooved. Matching grooves roll onto the pipe ends, a gasket seats between the barrel and the fitting, and a split housing or clamp bolts over the groove to hold the joint closed. Grooved assembly lines up faster than welding on a live route, and the joint can be broken back open with hand tools when maintenance needs access. The gasket material and housing torque follow the listed pressure and temperature envelope on the drawing.

How the joint behaves under service depends on the end form chosen for that line. Welded ends fuse into a rigid connection that moves with the pipe, but they need a qualified weld procedure, joint fit-up and post-weld inspection as the quality plan requires. Threaded ends come apart with standard tools, which keeps maintenance simple on small-bore branches, while grooved and push-on seats rely on gasket compression to seal under pressure and allow a small angular deflection after laying. Each end family suits a different line, and the choice follows the spool list rather than a default picked at the warehouse counter.

ItemDetail
Product categoryCross
Pressure rating1.6MPa
Body materialQT450 Ductile Iron
Section shapeMechanical Cross
Listed standardGB
Model referenceXGQT
Listed size rangeDN80 to DN200
End connectionGrooved
Intended serviceFire protection piping

Batch practice and order terms

The listed minimum order sits at Min. Order: 1 Piece, and the FOB bracket runs US $14-22 / Piece. The delivery window is not fixed on the listing and is agreed with the buyer at order confirmation. Pieces carry the YH mark and ship from China, and custom dimensions are accepted where the line falls outside a standard stock range.

The listing leaves any open field to be confirmed against the project drawing; no certificate number or rating is assumed where the source record leaves it blank.

Mechanical crosses on the street main

On site, the piece is handled with a sling or soft cradle rather than dropped onto the rack, and the end protection stays on until the joint is ready to close. Support clips and hangers are spaced to the span conditions on the drawing, so the body does not sag under its own weight between anchors. Where the run crosses a trench, chamber or equipment tie-in, the fitting is aligned square before the joint is tightened or welded; a skewed seat leaves one side under-compressed and shows weeping once pressure comes on. Crews record the line size, end form and pressure class on the spares tag, so the next replacement pulled from the store matches the existing run.

Hot Tags: Ductile Iron Mechanical Grooved Cross, China Ductile Iron Mechanical Grooved Cross manufacturers, carbon steel adapter fittings, carbon steel industrial piping components, carbon steel pipe fitting, carbon steel plug fittings, carbon steel process fittings, pvc pipe fittings

Send Inquiry

whatsapp

Phone

E-mail

Inquiry