Resin Glass Fiber Trench Drainage Cover
video

Resin Glass Fiber Trench Drainage Cover

Resin composite trench floor grate in resin and glass fiber, standard panel 1.22×3.66m, anti-slip and ISO certified. Commonly used for drainage channels, walkways and parking lot floors.
Custom sizes are available, FOB pricing runs US $1.9-10 per piece, min. order 10 pieces. OEM orders are welcome.
Send Inquiry
Product Introduction

Resin Glass Fiber Trench Drainage Cover

Trench floors beside channels and parking bays

This drainage cover sits over trench floors and drainage channels in walkways, parking lot floors and other paved areas where surface runoff collects in a linear slot at the low edge of the bay. The listed usage covers drainage and anti-slip service, so the panel spans the open channel while its top surface gives a sure step for foot traffic and light wheeled movement across the floor. Trench floor grates appear along parking lot bay edges, beside walkway channels and in the drainage strips between paved sections, where water from rain and washdown needs to leave the hard surface without pooling. The panel rests on the channel ledges at each side, and flush seating keeps the rim level with the surrounding floor so a cart or foot traffic crosses the slot without a step. Parking lot duty mixes pedestrian movement with occasional vehicle wheel pass-by at slow speed, and the cover section is selected to match the traffic condition recorded on the site drawing. Anti-slip character comes from the composite face and open mesh, not a separate coating that wears under repeated crossing.

The drainage cover spans the trench channel at the bay edge. Mesh drains runoff while the face stays anti-slip.

Resin and glass fiber over open drains

Body material combines resin with glass fiber, a composite build that stays light for trench-side handling and tolerates damp service without a steel frame to rust. The model reference field reads Resin, and the listed dimensions are 1.22 by 3.66 m, marked customizable on the source sheet, so panels can be cut to the channel width and length shown on the site drawing. Glass fiber reinforcement carries bending across the panel width while the resin binds the mesh and forms the non-metallic top surface; the panel will not leave oxide stains on concrete or paving in wet service. Setting follows channel preparation: trench edges are squared, support ledges checked level, and panels dropped into place without forcing the rim against the floor finish. Open mesh lets water drop through while blocking coarse debris that would settle in the channel below. Composite panels of this build do not pick up surface magnetism, which can matter near buried electrical runs along parking lot drainage strips. Buyers comparing against cast iron grates for paved-area duty usually weigh the lighter handling first, then the non-rusting finish in damp service.

Resin and glass fiber carry the panel bending load. Standard panels are customizable to channel width.

Anti-slip surface on a composite panel

Anti-slip performance on this trench floor grate comes from the textured composite face combined with the open mesh pattern, which drains liquid away from the step rather than leaving a wet film on a solid plate. Parking lot and walkway channels see rain, occasional washdown and tracked-in moisture, and the panel surface must hold traction under shoes and light wheels across those conditions. Mesh openings are sized to pass surface water without forming slots wide enough to trap small wheels or heels, and the edge bars frame the panel so the rim sits flat on the channel ledge. Where the grate runs along a walkway edge, its line aligns with the paving joint to keep the walking band clear of the mesh. Site cleaning routines should follow the composite material's service tolerance; pressure washdown at the channel clears silt from the slot and keeps drain capacity through wet seasons. After fitting, a walk along the panel line checks flush edges, firm seating and any rocking rim before the paved area opens to traffic.

Textured face and mesh give anti-slip traction over wet floors. Flush rim seating is checked along the panel line.

Resin composite trench floor drainage cover over a paved channel
Glass fiber resin grate panel staged beside a parking lot drainage trench.

Custom dimensions for non-standard trenches

The listing marks the 1.22 by 3.66 m panel family as customizable, which matters where trench widths in older paved areas differ from the standard rectangle or where a channel turns or narrows between bay sections. Cut lengths follow the measured channel between ledges, and side edges are dressed to sit flush against the trench wall so washdown water does not run down a side gap. Non-standard opening layouts can be requested when the site drawing calls for narrower or wider mesh spacing. Certification on the source sheet reads ISO; joint form, pressure class and model detail fields remain open beyond the Resin reference, and those entries should be matched to the site specification before selection. Composite material in trench service handles standing moisture and mild cleaning agents within its service tolerance, and panels are replaced in sections when an edge cracks or a mesh bar loosens rather than rebuilding the whole channel frame. Where the trench crosses a drive aisle, the panel section and load condition should be confirmed against the drawing before ordering.

Non-standard trench widths are cut to measured ledge dimensions. Certification record on the listing reads ISO.

SheetField
Brand markYH
Body materialResin + Glass Fiber
Listed dimensions1.22×3.66m (Customizable)
Model referenceResin
Certification recordISO
Minimum orderMin. Order: 10 Pieces
Listed formTrench Floor Grate
Product categoryGrating
Price bracketUS $1.9-10 / Piece
Country of originChina
Joint form-
Load class field-
Intended serviceDrainage, Anti-Slip
Delivery window-

Commercial basis for a trench floor grate

FOB pricing runs US $1.9-10 per piece with a minimum order of 10 pieces; the delivery window field on the source listing carries no assigned value, so production scheduling is agreed with the buyer at order confirmation. Brand mark YH, origin China, product type grating, and the type field records trench floor grate. The model reference reads Resin, and listed dimensions are 1.22 by 3.66m (Customizable). Certification record ISO; pressure class and joint form remain open fields on the sheet. Custom sizes and OEM arrangements are accepted where the paved-area project falls outside the standard panel family. Before shipment the shop checks panel dimensions against the listed size family, composite surface finish and mesh bar seating across each section. A trial order can start at the listed floor quantity; commercial figures sit in the table, and drawings should note channel width, cut length and traffic condition before production opens.

The listed minimum order is 10 pieces. Delivery schedule is agreed at order confirmation on open fields.

Hot Tags: Resin Glass Fiber Trench Drainage Cover, China Resin Glass Fiber Trench Drainage Cover manufacturers, Anti Clog Drain Grate, cast iron storm grate, drainage channel storm grate, municipal stormwater cover, Resin drain grate, street drain grate

Send Inquiry

whatsapp

Phone

E-mail

Inquiry