Stainless Steel Water Pipe 6 mm 630 mm
video

Stainless Steel Water Pipe 6 mm 630 mm

Stainless steel water pipe for laboratory gas distribution, ASTM A312/A213/GB/T 14976, OD 6 to 630mm, wall 1 to 50mm, 6-meter length. Commonly used on gas distribution and water, oil supply lines.
Customized sizes are accepted, FOB pricing runs US $680-1,500 per piece, min. order 1 piece.
Send Inquiry
Product Introduction

Stainless Steel Water Pipe 6 mm 630 mm

Gas distribution runs beside lab benches

This stainless steel water pipe serves laboratory gas distribution along with water and oil supply lines, running along bench fronts, service corridors and equipment connections in laboratory buildings. The listed outside diameter spans 6 mm to 630 mm, and the barrel is supplied in standard 6 meter lengths that are cut and fitted to the spool list. Smooth internal surface keeps the bore clean for gas and fluid transfer, and the uniform wall carries pressure and support loads along the span. The pipe appears on utility distribution runs where atmospheric damp and occasional chemical splash are expected, and the drawing confirms grade and end preparation against the fluid carried on that line.

Lab fitters watch the thread and end prep closely. A mismatched joint means a return trip to the bench.

Material and listed standard references

The body is stainless steel, chosen for wet service and resistance to mild chemical exposure. The material welds and machines cleanly when end preparation is needed on site, and it arrives with a plain surface; any paint, wrap or coating follows the project's own corrosion practice after the piece enters the run. Grade and finish are confirmed against the line specification before the order is cut, since the listed record leaves grade selection open on the source listing.

Before the piece leaves the plant, surface condition and dimensions are checked against the listing record, and any burr, casting flash or uneven thread is dressed back to the body profile. Wall thickness and outside diameter are sampled against the listed size range, and the end faces are protected with thread or end caps until the joint is ready to close. On site, crews brush grit from the bore and the sealing face before assembly, because sand or scale left on a thread or gasket seat is the usual reason a fresh connection weeps after the first pressure test. Spare pieces ride along with the next valve or fitting order, held in the maintenance store by line size and end type so the replacement matches the run it serves.

Stainless steel water pipe for laboratory gas and oil supply distribution
Stainless distribution barrel laid out for lab gas and supply service.

Outside diameter range on the listing

The listed size range reads 6mm–630mm on the source record. No fixed pressure class is assigned on the source listing, so line rating should be confirmed against the piping specification before installation. Listed standards and certification references read ASTM A312, ASTM A213, GB/T 14976, copied as they appear on the source listing; the drawing should confirm the applicable grade and test record before fabrication. Listed service on the source record: Water Supply, Gas Supply, Oil Pipe.

Dimension selection starts from the flow requirement on the line drawing, then narrows against pressure class, span length and the end form listed for that fitting. Where two sizes sit close on the range, the larger wall and diameter give margin against transient surge and support loads, while the smaller size keeps weight and cost down on branches that carry little flow. The drawing should fix outside diameter, wall thickness and end preparation before the order is cut, so the workshop does not guess at a dimension that falls outside the listed stock range. Spare sets are held in the maintenance store tagged by line size, end form and pressure class, which keeps the replacement matched to the run it serves. On installation, supports and hangers follow the span conditions listed for that pipe. The joint is aligned square before bolts come tight or welds are laid down.

Joining the barrel to service and supply lines

No fixed end connection is assigned on the source listing. How the piece joins the next section follows the fluid, diameter and assembly method stated on the project drawing, and the end preparation should be confirmed before the order is cut.

How the joint behaves under service depends on the end form chosen for that line. Welded ends fuse into a rigid connection that moves with the pipe, but they need a qualified weld procedure, joint fit-up and post-weld inspection as the quality plan requires. Threaded ends come apart with standard tools, which keeps maintenance simple on small-bore branches, while grooved and push-on seats rely on gasket compression to seal under pressure and allow a small angular deflection after laying. Each end family suits a different line, and the choice follows the spool list rather than a default picked at the warehouse counter.

EntryFigure
Body materialStainless Steel
Model referenceASTM A312 ASTM A269 ASTM A213
Intended serviceWater Supply, Gas Supply, Oil Pipe
Listed size range6mm–630mm
Section shapeStainless Steel Pipe
Pressure rating-
Product categoryWater Pipe
End connection-
Listed standardASTM A312, ASTM A213, GB/T 14976

Custom dimensions and batch practice

The listed minimum order sits at Min. Order: 1 Piece, and the FOB bracket runs US $680-1,500 / Piece. The delivery window is not fixed on the listing and is agreed with the buyer at order confirmation. Pieces carry the YH mark and ship from China, and custom dimensions are accepted where the line falls outside a standard stock range.

The listing leaves any open field to be confirmed against the project drawing; no certificate number or rating is assumed where the source record leaves it blank.

Service branches around the lab bench

On site, the piece is handled with a sling or soft cradle rather than dropped onto the rack, and the end protection stays on until the joint is ready to close. Support clips and hangers are spaced to the span conditions on the drawing, so the body does not sag under its own weight between anchors. Where the run crosses a trench, chamber or equipment tie-in, the fitting is aligned square before the joint is tightened or welded; a skewed seat leaves one side under-compressed and shows weeping once pressure comes on. Crews record the line size, end form and pressure class on the spares tag, so the next replacement pulled from the store matches the existing run.

Hot Tags: Stainless Steel Water Pipe 6 mm 630 mm, China Stainless Steel Water Pipe 6 mm 630 mm manufacturers

Send Inquiry

whatsapp

Phone

E-mail

Inquiry