Stainless Steel Wafer Check Valve Guided
Custom orders are accepted, FOB pricing runs US $14.49 per piece, min. order 100 pieces.
Stainless Steel Wafer Check Valve Guided
Hydrocarbon transfers between tank, pump and loading arm
The listed duty is industrial usage, water industrial usage, household usage, and this wafer check valve sits at fuel, hydrocarbon and process lines, where forward flow opens the disc and any reversal closes it again. Behind the pump outlet the valve sits close to the discharge flange, where the straight run before it keeps the disc moving freely; a sharp elbow or reducer right upstream can make the disc hang open or chatter against the seat. On a transfer skid this check often pairs with a pressure gauge and a small drain, and the maintenance store keeps a spare disc and seat insert for the sizes most often worked on. Buyers match the bore to calculated line flow, then confirm the rating against the highest pressure the line sees during start-up and shut-down rather than steady running pressure. The spare matches the installed main.
The listed size band and working rating are shown in the table below for reference before selection.

Stainless body resistant to fuel contact and vapour
The material sees both the pumped or flowing fluid and the occasional external spray in the plant; buyers match the body metal to the most aggressive fluid on the line rather than the cleanest sample. Where the duty carries grit or condensate, crews look at the seat first, since a worn seat shows up as a weep after shut-down and the body itself often still has service left in it. External surface stays plain as delivered; paint or wrapping follows the plant's corrosion practice after fit-up. Wall thickness carries internal pressure and small loads from clips and supports, and castings with surface flaws are rejected before the seat is fitted. Mixed-material entries require confirming which metal contacts the fluid, since shell and wetted parts can differ. The body metal is matched to the most aggressive fluid expected on the run rather than the cleanest sample, because wetted surfaces see pumped product continuously while the shell only meets ambient moisture and occasional spray during access.
Wafer end between flanges on the fuel skid
On wafer jobs the spacer length between flanges stays short, which helps in cramped pump stations and skids where overall length matters. Flanged versions leave a wider sealing face and are preferred where the line may be broken open often; the joint torque follows the flange standard on the project drawing, and the gasket is centered before the bolts go cross-sequence.
| Field | Figure |
|---|---|
| What the body is cast or made from | Stainless Steel |
| Listed type of the assembly | Wafer Check Valve |
| What the valve family is listed as | Wafer Check Valve |
| Duty the piece is assigned to | Industrial Usage, Water Industrial Usage, Household Usage |
| How the ends join the line | Wafer |
| Working rating across the bore | Pn10, Pn16 |
| Nominal bore range covered | DN50-DN200 |
| Approval reference on the entry | ANSI |
| Model reference on the listing | DN50-DN200 |
Disc closure as pump pressure falls away
Forward pressure lifts the disc and opens the bore; the flow holds it open while the line runs. On trip, pressure drop or downstream pushback, the disc returns to the seat and seals the reverse path. The class is set against maximum pressure with surge included, not average running pressure. When the check chatters after long service, crews clean the sealing face, check the guide for grit and turn over the insert before condemning the body. A worn pin or guide face is the usual cause of a rattle, and these parts renew far cheaper than a housing replacement. The pressure class on the listing is chosen against peak surge, so a class picked on average pressure may weep when reversal arrives. Over repeated cycles the hinge surfaces and guide faces take the brunt of the movement, and these parts show wear before the housing does, so a rattle or chatter should be traced to pin, guide or seat before any decision to replace the casting. The setting follows the project drawing.
The store keeps sealing parts grouped by bore and end form. Inserts, pins and guides wear first, and these are held for the busiest sizes instead of a full spare valve for every diameter. A rattle usually means grit on the seat or a worn pin, and early attention avoids a weep after trip-off. Castings that have held pressure rarely need replacement once sealing parts are renewed.
Bore is chosen from the listed diameter band against calculated line flow, and the pressure class is matched to the maximum pressure the line reaches during start-up, trip and shut-down rather than its steady running figure. Buyers note end form, seat compound and rating when a spare is ordered, so the replacement matches the installed main instead of a generic stock piece. Notes go in the maintenance record.
Before the valve enters the run, crews match the end type to the adjacent flange or weld preparation and check that the moving element travels freely between the closed and open stops. Sealing faces are wiped clean of grit, and thread or flange protectors stay on until the joint is ready to close, so no debris lodges between seat and closure during commissioning. The first pressure test after fit-up reveals any weep early, before the line is handed over to operation.
Seat problems surface on the initial test before any body weakness appears, and the record should note bore, end form and rating when the sealing part is replaced so the spare matches the installed main.
Fuel system spares by bore and ANSI rating
Size runs DN50-DN200 and the rating covers Pn10, Pn16; the order should confirm bore, end form, seat type and pressure class against the piping drawing. The listing records ANSI as the standard reference. A trial order can start with one piece where the listing allows; the price bracket and delivery window are settled with the quotation once bore, end form and quantity are confirmed.
Hot Tags: Stainless Steel Wafer Check Valve Guided, China Stainless Steel Wafer Check Valve Guided manufacturers, air check valve, brass check valve, hydraulic check valve, low pressure check valve, Socket Weld Check Valve, Stainless Steel Lift Check Valve
You Might Also Like
Send Inquiry














