Seamless Stainless Steel Process Pipe
video

Seamless Stainless Steel Process Pipe

Seamless stainless steel water pipe, 6 m length, OD 6-630 mm, wall 1-50 mm, made to ASTM A312, ASTM A213 and GB/T 14976. Used on deep-sea drilling support and oil/gas process lines.
Custom dimensions are accepted and OEM is welcome. FOB price runs from US $1,000-2,500 per piece, MOQ 1 piece.
Send Inquiry
Product Introduction

Seamless Stainless Steel Process Pipe

Support lines on deep-sea drilling spreads

This seamless stainless steel water pipe supports deep-sea drilling spreads and carries oil, gas and water process lines on offshore process packages. The listed outside diameter spans 6 mm to 630 mm, and the barrel comes in standard 6 meter lengths cut to the spool list. The uninterrupted seamless wall keeps the bore clean and gives uniform thickness around the circumference where pressure and external loads both bear on the body. The pipe appears on process headers, utility runs and transfer lines serving drilling support equipment, and the drawing confirms grade and end preparation against the fluid and ambient conditions on that line.

Offshore crews order spares by line tag. The end form and diameter have to match before the next supply boat leaves.

Seamless barrel against marine duty

The barrel is a seamless stainless steel section, drawn or extruded without a longitudinal weld seam. That smooth, uninterrupted wall keeps the bore clean and gives the section uniform thickness around the circumference, which matters where internal pressure and external support loads both bear on the pipe body. The seamless construction leaves no seam weld to inspect after installation, and the plain surface accepts whatever external protection the project drawing calls for. Wall selection follows the pressure and span conditions listed on the line drawing, not a default stock thickness.

Before the piece leaves the plant, surface condition and dimensions are checked against the listing record, and any burr, casting flash or uneven thread is dressed back to the body profile. Wall thickness and outside diameter are sampled against the listed size range, and the end faces are protected with thread or end caps until the joint is ready to close. On site, crews brush grit from the bore and the sealing face before assembly, because sand or scale left on a thread or gasket seat is the usual reason a fresh connection weeps after the first pressure test. Spare pieces ride along with the next valve or fitting order, held in the maintenance store by line size and end type so the replacement matches the run it serves.

Seamless stainless steel pipe for deep-sea drilling support and oil gas lines
Seamless stainless barrel laid out for offshore drilling support service.

Listed diameter and wall practice

The listed size range reads OD 6-630 mm on the source record. No fixed pressure class is assigned on the source listing, so line rating should be confirmed against the piping specification before installation. Listed standards and certification references read ASTM A312, ASTM A213, GB/T 14976, copied as they appear on the source listing; the drawing should confirm the applicable grade and test record before fabrication. Listed service on the source record: Water Supply, Gas Supply, Oil Pipe.

Dimension selection starts from the flow requirement on the line drawing, then narrows against pressure class, span length and the end form listed for that fitting. Where two sizes sit close on the range, the larger wall and diameter give margin against transient surge and support loads, while the smaller size keeps weight and cost down on branches that carry little flow. The drawing should fix outside diameter, wall thickness and end preparation before the order is cut, so the workshop does not guess at a dimension that falls outside the listed stock range. Spare sets are held in the maintenance store tagged by line size, end form and pressure class, which keeps the replacement matched to the run it serves. On installation, supports and hangers follow the span conditions listed for that pipe. The joint is aligned square before bolts come tight or welds are laid down.

Oil, gas and water process connections

No fixed end connection is assigned on the source listing. How the piece joins the next section follows the fluid, diameter and assembly method stated on the project drawing, and the end preparation should be confirmed before the order is cut.

How the joint behaves under service depends on the end form chosen for that line. Welded ends fuse into a rigid connection that moves with the pipe, but they need a qualified weld procedure, joint fit-up and post-weld inspection as the quality plan requires. Threaded ends come apart with standard tools, which keeps maintenance simple on small-bore branches, while grooved and push-on seats rely on gasket compression to seal under pressure and allow a small angular deflection after laying. Each end family suits a different line, and the choice follows the spool list rather than a default picked at the warehouse counter.

PieceMarking
End connection-
Pressure rating-
Listed size rangeOD 6-630 mm
Intended serviceWater Supply, Gas Supply, Oil Pipe
Model reference-
Listed standardASTM A312, ASTM A213, GB/T 14976
Product categoryWater Pipe
Body materialSeamless Stainless Steel
Section shapeWater Pipe

Custom sizes and dispatch notes

The listed minimum order sits at Min. Order: 1 Piece, and the FOB bracket runs US $1,000-2,500 / Piece. The delivery window is not fixed on the listing and is agreed with the buyer at order confirmation. Pieces carry the YH mark and ship from China, and custom dimensions are accepted where the line falls outside a standard stock range.

The listing leaves any open field to be confirmed against the project drawing; no certificate number or rating is assumed where the source record leaves it blank.

Offshore support lines on the process package

On site, the piece is handled with a sling or soft cradle rather than dropped onto the rack, and the end protection stays on until the joint is ready to close. Support clips and hangers are spaced to the span conditions on the drawing, so the body does not sag under its own weight between anchors. Where the run crosses a trench, chamber or equipment tie-in, the fitting is aligned square before the joint is tightened or welded; a skewed seat leaves one side under-compressed and shows weeping once pressure comes on. Crews record the line size, end form and pressure class on the spares tag, so the next replacement pulled from the store matches the existing run.

Hot Tags: Seamless Stainless Steel Process Pipe, China Seamless Stainless Steel Process Pipe manufacturers

Send Inquiry

whatsapp

Phone

E-mail

Inquiry