Stainless Steel DN15 DN50 Pipe Elbow
Custom sizes are available on request. FOB price US $1.8-90 per piece, minimum order 10 pieces.
Stainless Steel DN15 DN50 Pipe Elbow
Cooling water and utility runs at the block
This stainless steel elbow sits in cooling water and plant utility lines at power generation stations, turning runs between boiler decks, pump houses and auxiliary equipment on the plant rack. The listed size range covers DN15 to DN50, small-bore sections that fit compact manifolds and instrument branches. The stainless body resists wet service and mild atmospheric exposure around cooling circuits, and it welds and machines cleanly when end preparation is needed on site. End choices on the listing include butt weld, socket weld and threaded, so the matching version is packed for each line type on the spares list. Crews check the end form against the existing run before a spare goes onto the maintenance shelf.
Maintenance stores keep these by DN size. A wrong end form means a second trip to the rack.
Stainless body for wet plant service
The body is stainless steel, chosen for wet service and resistance to mild chemical exposure. The material welds and machines cleanly when end preparation is needed on site, and it arrives with a plain surface; any paint, wrap or coating follows the project's own corrosion practice after the piece enters the run. Grade and finish are confirmed against the line specification before the order is cut, since the listed record leaves grade selection open on the source listing.
Before the piece leaves the plant, surface condition and dimensions are checked against the listing record, and any burr, casting flash or uneven thread is dressed back to the body profile. Wall thickness and outside diameter are sampled against the listed size range, and the end faces are protected with thread or end caps until the joint is ready to close. On site, crews brush grit from the bore and the sealing face before assembly, because sand or scale left on a thread or gasket seat is the usual reason a fresh connection weeps after the first pressure test. Spare pieces ride along with the next valve or fitting order, held in the maintenance store by line size and end type so the replacement matches the run it serves.

Small bore size range and end forms
The listed size range reads DN15-DN50 on the source record. No fixed pressure class is assigned on the source listing, so line rating should be confirmed against the piping specification before installation. The certification record on the listing is left open; no standard or certificate number is assigned in the source record. No fixed service field is assigned on the listing; the piece follows the fluid and conditions stated on the project drawing.
Dimension selection starts from the flow requirement on the line drawing, then narrows against pressure class, span length and the end form listed for that fitting. Where two sizes sit close on the range, the larger wall and diameter give margin against transient surge and support loads, while the smaller size keeps weight and cost down on branches that carry little flow. The drawing should fix outside diameter, wall thickness and end preparation before the order is cut, so the workshop does not guess at a dimension that falls outside the listed stock range. Spare sets are held in the maintenance store tagged by line size, end form and pressure class, which keeps the replacement matched to the run it serves. On installation, supports and hangers follow the span conditions listed for that pipe. The joint is aligned square before bolts come tight or welds are laid down.
End choices on the plant rack
Three end families appear on the listing: butt weld, threaded and socket weld. Butt weld ends prepare straight bevels that fuse to matching pipe in a rigid, leak-tight joint suited to larger process and steam runs. Threaded ends accept standard pipe on smaller lines and let maintenance crews remove a section without cutting. Socket weld ends slide the pipe into a recessed bore before fillet welding, a common choice for compact branch and instrument connections. When the spares list splits by line type, the matching end version is packed for each run, so the crew does not convert one end form into another on site.
How the joint behaves under service depends on the end form chosen for that line. Welded ends fuse into a rigid connection that moves with the pipe, but they need a qualified weld procedure, joint fit-up and post-weld inspection as the quality plan requires. Threaded ends come apart with standard tools, which keeps maintenance simple on small-bore branches, while grooved and push-on seats rely on gasket compression to seal under pressure and allow a small angular deflection after laying. Each end family suits a different line, and the choice follows the spool list rather than a default picked at the warehouse counter.
| Record | Nominal |
|---|---|
| Listed standard | - |
| Intended service | - |
| Pressure rating | - |
| Model reference | - |
| End connection | Butt Weld, Socket Weld, Threaded |
| Product category | Elbow |
| Section shape | Elbow |
| Body material | Stainless Steel |
| Listed size range | DN15-DN50 |
Spare sets and order minimum
The listed minimum order sits at Min. Order: 10 Pieces, and the FOB bracket runs US $1.8-90 / Piece. The delivery window is not fixed on the listing and is agreed with the buyer at order confirmation. Pieces carry the YH mark and ship from China, and custom dimensions are accepted where the line falls outside a standard stock range.
The listing leaves any open field to be confirmed against the project drawing; no certificate number or rating is assumed where the source record leaves it blank.
Cooling water spares on the station rack
On site, the piece is handled with a sling or soft cradle rather than dropped onto the rack, and the end protection stays on until the joint is ready to close. Support clips and hangers are spaced to the span conditions on the drawing, so the body does not sag under its own weight between anchors. Where the run crosses a trench, chamber or equipment tie-in, the fitting is aligned square before the joint is tightened or welded; a skewed seat leaves one side under-compressed and shows weeping once pressure comes on. Crews record the line size, end form and pressure class on the spares tag, so the next replacement pulled from the store matches the existing run.
Hot Tags: Stainless Steel DN15 DN50 Pipe Elbow, China Stainless Steel DN15 DN50 Pipe Elbow manufacturers, food grade stainless fittings, Seamless Stainless Steel Elbow, Seamless Stainless Steel Tee, stainless steel low leakage fittings, stainless steel pipe union, stainless steel threaded connector
You Might Also Like
Send Inquiry














