Resin Non-magnetic Sewer Cover Panel
video

Resin Non-magnetic Sewer Cover Panel

Resin composite non-magnetic drain walkway grates, lightweight and corrosion-resistant. Standard size 1.22x3.66 m, customizable, used for drainage channels and anti-slip municipal walkways.
Custom sizes are accepted and OEM is welcome. FOB price runs from US $1.9-10 per piece, MOQ 10 pieces.
Send Inquiry
Product Introduction

Resin Non-magnetic Sewer Cover Panel

Non-magnetic resin over utility trenches

This sewer cover spans utility trenches and drainage slots along municipal walkways, where a non-metallic panel avoids magnetic interference with buried cables and service lines running alongside the channel. The listed usage covers drainage and anti-slip walkway service, so the panel top drains surface liquid while giving a firm, anti-slip step for pedestrian traffic across the walking route. Non-magnetic character matters near underground electrical runs, signal cables and utility chambers that share the trench corridor, where a ferrous cover would influence nearby magnetic fields. The resin body does not conduct magnetism or electricity, which keeps the panel clear of interference concerns in mixed utility alignments. Walkway drainage slots follow the edge of the paving rather than crossing the main walking band, and the cover mesh keeps loose debris out of the trench while water passes through. Where the panel adjoins a utility chamber access, the rim sits flush with the sidewalk so crews cross the cover line without a step.

The non-metallic panel avoids magnetic interference near cable runs. Mesh drains surface water along the walkway slot.

Anti-slip walkway surface in composite

Body material is resin, recorded also in the model reference field, a light composite that tolerates damp walkway service without a steel frame or rusted fasteners. The panel family measures 1.22 by 3.66 m, cut to the trench width shown on the municipal walkway drawing, and the open mesh spans the channel with edge bars resting on the support ledge at each side. Anti-slip performance comes from the textured composite face combined with the open mesh pattern, which drains tracked-in moisture rather than holding a wet film on a solid plate. Pedestrian duty sets the mesh spacing: openings pass water without forming slots wide enough to trap heels or small wheels in high-footfall sections. Resin surface resists scuffing from boots and stroller wheels in routine walkway service, and the composite does not leave oxide marks on surrounding paving. Setting follows trench preparation: edges squared, ledges checked level, panels seated flush so no rim lip catches shoe soles. Lightweight composite panels reach lower walkway sections through ordinary handling without lifting equipment.

Resin body stays non-magnetic and light for walkway handling. Mesh spacing avoids heel and wheel traps.

Panel dimensions and cut-to-fit edges

Listed panel size is 1.22x3.66 m, and trench openings in municipal walkways rarely match that standard rectangle exactly, so panels are trimmed to the measured channel width and length before fitting. Edge fit matters on pedestrian routes: a panel that sits short leaves a gap for toes and debris to fall through, while a panel forced into an undersized opening lifts at one corner and rocks under foot traffic. The walkway drawing marks trench runs and channel centers, and cut lengths follow those centers with the rim resting on the ledge at each side. Where the cover meets a utility chamber frame or a paving joint, the panel end is trimmed square to that edge and any side gap sealed against wash-in. Mesh layout can be adjusted to site conditions when the drawing calls for narrower or wider openings. A final walk along the panel line checks flush edges, level seating and a firm non-rocking step before the walkway opens to the public.

Standard panels are cut to measured trench widths. Flush rim edges are checked along the walkway line.

Resin non-magnetic sewer cover panel over a municipal walkway trench
Composite grating panel staged along an anti-slip municipal drainage walkway.

Resin body in wet drainage service

Walkway drainage service keeps the panel in intermittent contact with rainwater, spillage and routine washdown, and the resin composite handles that damp cycle without oxide formation or metal corrosion. The non-metallic surface dries between wet passes rather than holding a damp film, and it resists mild cleaning agents used in municipal walkway maintenance within the material's service tolerance. Composite panels do not absorb water the way porous castings or untreated timber do, and the finish stays clean on light sidewalk paving. Certification, pressure class and joint form fields carry no assigned value on the source listing, so those entries should be confirmed against the municipal walkway drawing rather than assumed from the material. Where the trench runs near buried utility cables, the non-magnetic body removes one interference consideration from the cover selection. Panels are replaced in sections when an edge cracks or a mesh bar loosens, without rebuilding the whole trench frame.

Resin body handles damp cycles without oxide streaks. Open certification and class fields are confirmed against the drawing.

SlabUse
Brand markYH
Body materialResin
Listed dimensions1.22x3.66 m
Model referenceResin
Certification record-
Minimum orderMin. Order: 10 Pieces
Listed formGrating
Product categoryGrating
Price bracketUS $1.9-10 / Piece
Country of originChina
Joint form-
Load class field-
Intended serviceDrainage, Anti-Slip Walkway
Delivery window-

Sizing a non-magnetic cover order

FOB pricing on the listing runs US $1.9-10 per piece with a minimum order of 10 pieces; the delivery window field carries no assigned value, so production scheduling is agreed with the buyer at order confirmation. Brand mark YH, origin China, product type grating, and the type field records the same grating form. Model reference Resin; listed dimensions 1.22x3.66 m; certification record open on the sheet. Custom panel sizes are accepted when walkway trench geometry falls outside the standard family. Before packing the shop checks panel dimensions against the listed size, resin surface finish and mesh bar seating across each section. A trial order can start at the listed floor quantity; commercial figures sit in the table, and drawings should note trench width, cut length and any special edge treatment before production opens.

Ten pieces is the listed order floor. The sewer cover cut lengths follow the measured municipal walkway trench.

Hot Tags: Resin Non-magnetic Sewer Cover Panel, China Resin Non-magnetic Sewer Cover Panel manufacturers, Anti Clog Drain Grate, Debris resistant drain grate, drainage channel storm grate, municipal stormwater cover, Steel Grating Drain Grate, street drain grate

Send Inquiry

whatsapp

Phone

E-mail

Inquiry