Stainless Steel Flanged Gate Valve
Min. order is 1 piece, FOB pricing runs US $28.2-62.5 per piece. Custom ends available.
Stainless Steel Flanged Gate Valve
Industrial water mains where corrosion resistance matters
Isolation duty on this run falls to the wedge gate at industrial water and corrosive process lines, where crews need a valve that seals fully open or fully closed rather than a regulating trim. Access around the wedge decides where the gate lands on the header or branch; the handwheel or drive needs clearance to turn, and the bonnet needs room for packing renewal. Bore is taken from the listed diameter band, and the class follows peak line pressure including trip and slam surge. These block valves appear on pump headers, cooling loops and drain branches across station and plant piping. The setting follows the project drawing.
The table below carries the listed size band and working rating recorded for this valve listing.

Stainless body across DN15 to DN600
Housing metal on this entry is Stainless Steel; the casting carries pressure, stem thrust and small external loads from supports along the main. The wedge seats against body rings, and the wedge against stainless seat faces sets how the closure meets the bore. Body wall and rating are confirmed against maximum line pressure rather than average working pressure. Before bonnet and wedge are fitted, the casting is checked for surface flaws and bore dimensions, and sealing faces are matched to the seat ring. External corrosion resistance follows the housing metal, and a spare wedge and packing set covers the most cycled sizes without stocking a complete valve per diameter. Bonnet bolts go cross-sequence so the housing seats evenly on the body flange. The wedge, rings and packing share the sealing duty while the shell carries pressure, and buyers keep spare wedge and packing sets for the most cycled sizes rather than holding a complete valve for every diameter on the line.
Four end forms on the same wedge platform
The connection listed is Flanged / Threaded / Butt Welded / Socket Weld. Raised-face and ring-joint flanges bolt to matching line flanges through a gasket, while butt weld ends prepare a bevel that fuses to the pipe in a rigid joint.
| Item | Detail |
|---|---|
| What the body is cast or made from | Stainless Steel |
| End form matched to the spool | Flanged / Threaded / Butt Welded / Socket Weld |
| Nominal bore range covered | DN15–DN600 |
| Duty the piece is assigned to | Water Industrial Usage, Flow Control |
| Model reference on the listing | - |
| Listed type of the assembly | Gate Valve |
| Standard record attached to the listing | GB, DIN, JIS, BSW, ANSI |
| Working rating across the bore | Class 150 / Class 300 / Pn16 / Pn25 / Pn40 |
| What the valve family is listed as | Wedge Gate Valve |
Class and Pn ratings covering heavier line pressure
Pressure acts on the wedge from either side once seated, and the body, bonnet and flange neck carry that load without permanent deflection. Wedge sealing depends on clean seat faces and even torque around the bonnet; grit left on a seat ring leaves one side under-sealed, and a hydrostatic test after fit-up shows any weep before the run is handed over. Stem packing keeps the line sealed around the rising or non-rising spindle and is replaced when it starts to drip. Partly open service rattles the wedge and scores the faces, so running duty keeps the valve fully open or fully closed. Packing seals around the spindle and renews on a drip, and the wedge is inspected for scoring at each bonnet opening. Shell, bonnet and neck hold seated pressure cycle after cycle without permanent deflection. Pressure on the seated wedge acts from both sides, and body, bonnet and neck carry that load cycle after cycle without permanent deflection, provided the seat faces stay clean and the bonnet bolts hold even torque around the housing. The spare matches the installed main.
Spare parts track the working parts inside the housing. Wedge, seat ring and stem packing are stocked for the sizes cycled most often on the line, and the packing is renewed on a slow drip before any weep reaches the flange joints or the bonnet seal. When the gate has been partly open and throttling for a stretch, crews inspect the wedge and seat faces for scoring before the next isolation duty is assigned to the valve. A rebuilt wedge usually returns to service, while a scored seat ring is replaced rather than lapped back into shape.
The metal sees internal fluid continuously and ambient moisture only around the flange and bonnet, so corrosion attention follows the wetted parts first. Coating, wrapping and external paint follow the plant's own corrosion practice once the piece enters the line, and the casting itself keeps service after the sealing parts are renewed. Inspect the exterior at each visit.
On site the valve is set in place with the correct flange bolts or weld bevel, and the closure is cycled once from fully closed to fully open to confirm the stem, disc or wedge moves without binding. Grit on the seat face is cleared before pressure is applied, and the joint is centered so the seal compresses evenly around the bore. A slow leak after the first test points to the seat rather than the shell, which is where maintenance attention usually starts.
A slow seat leak shows up on the first pressure test more often than a body failure, so maintenance attention goes to the insert, the hinge or guide surfaces and the sealing face before the casting itself is questioned.
Process spares matched to bore, end and standard
Bore DN15–DN600 under rating Class 150 / Class 300 / Pn16 / Pn25 / Pn40 is the listed range; confirm end form, seat type and pressure class against the project drawing before ordering. The listing records GB, DIN, JIS, BSW, ANSI as the standard reference. The first order may run to a single piece where permitted; pricing and lead schedule follow the quotation once size, end form and count are agreed.
Hot Tags: Stainless Steel Flanged Gate Valve, China Stainless Steel Flanged Gate Valve manufacturers, gate valve, mechanical gate valve, mining gate valve, split wedge gate valve, wastewater gate valve, Worm Gear Gate Valve
You Might Also Like
Send Inquiry














