Stainless Steel Rising Stem Gate Valve
Body grades CF8, CF8M, CF3M, 304, 316 and 316L are offered. FOB price US $30-699 per piece, minimum order 10 pieces.
Stainless Steel Rising Stem Gate Valve
Stainless steel isolation on oil and water pipelines
On oil and water pipelines, on transmission and distribution runs, this stainless steel gate valve handles the isolation point for flow control on oil and water pipelines needing full bore on or shut isolation. The body listed in the source data matches the nominal size range and pressure class shown in the specification table, and the seal arrangement follows the fluid and cycle frequency expected on that branch. End form is confirmed against the spool list. Site crews tend to ask which end type the spool carries before they quote a replacement, because a mismatched flange or thread delays the job more than a slightly longer delivery would, and the gasket face has to sit square before any bolt goes through. The valve sits in the run so flow passes through the open bore in one direction, and closure blocks the line when the stem or disc is driven to the shut position. Where the line crosses a crowded rack or a below-deck compartment, face-to-face length and actuator clearance are checked against the surrounding pipework before the valve is ordered. Keep the sealing face clean before packing.
Rating on paper is one figure; on site it comes down to spacing.
CF8M 316L body across DN50 to DN600
The shell follows stainless steel body, with CF8, CF8M, CF3M, 304, 316 and 316L grades offered, as recorded in the source listing. The sealing element uses rising stem and wedge inside the stainless shell for pipeline shut-off, and the choice between soft and metal seat depends on fluid chemistry, temperature and how often the valve cycles on that branch. The pressure band and nominal size range in the table set the limits the body is built to, and any service outside those bands should be confirmed against the project piping specification before installation. A soft seat closes cleanly on water and process loops; a metal seat tolerates particles and higher temperatures that would shorten elastomer life over repeated openings and closings. Internal motion stays inside the body shell, and the seal contact surface is kept clear of welding spatter and pipe scale during fit-up. The seal is checked at each outage. The size range and rating band are matched to the branch before a spare is issued from store. When the valve reaches the maintenance store, it is logged by size, seat type and end form so the right spare reaches the right branch on the next outage.

Rising stem and wedge inside the stainless shell
This stainless steel gate valve connects through flange ends to GB, DIN, JIS, BSW and ANSI across DN50 to DN600. The listing records the joint types available, and the installed end form follows the branch specification rather than a default picked from stock. Flanged connections bolt the body to mating flanges along a gasket face, while wafer bodies are clamped between flanges on through bolts and occupy a narrower face-to-face space. Where a welded end is listed, the pipe is prepared with a bevel or recess to suit the fusion procedure on that line. Alignment matters: the body should sit square between the flanges, and bolt tension is distributed in opposite sequence to avoid pinching one side of the joint and to keep the gasket compressed evenly around the whole flange perimeter. End form, flange face and bolt size are all matched to the pressure class on the source table before the valve leaves the workshop.
| Reserve | Note |
|---|---|
| Model reference | - |
| Nominal size range | DN50~DN600 |
| End connection | Flange |
| Pressure rating | Class 150 / Class 300 / Pn16 / Pn25 / Pn40 |
| Standard record | GB, DIN, JIS, BSW, ANSI |
| Listed service | Flow Control |
| Product category | Gate Valve |
| Valve family | Straight-through |
| Body casting | Stainless Steel |
Class 150, Class 300 and Pn rating bands
The listed driving arrangement for this stainless steel gate valve is set out in the source record. handwheel lifts the rising stem; wedge position follows spindle travel above the bonnet Motion from the handwheel, lever or actuator reaches the internal closure member through the stem, and the travel marks on the body or stem indicate whether the bore is open, shut or throttled at that point. Gearboxes and turbine handwheels multiply torque so a larger disc can be turned without a long pull on the lever, and pneumatic units allow remote shut-off from a control station. A rising stem shows wedge position as the spindle climbs; a non-rising stem keeps the spindle inside the bonnet and reads position from the handwheel or an indicator. The actuator or gearbox is sized to the disc torque at the listed pressure band. Stem packing and seal condition are checked during the same position-mark inspection. Branches that stay open for months are exercised on the maintenance schedule, so deposits do not weld the seat shut before the next isolation.
Pipeline spare valve selection records
Rating, size and service fields for this stainless steel gate valve are carried in the table that follows, copied from the source specification without added values; where a source field is left open, the listing keeps it open rather than assigning a default rating or certification. One piece can open a trial order, and the price bracket together with the delivery window are agreed when the quotation is settled; custom sizes or part marking are discussed only when the project calls for a non-standard configuration. Before installation, line rating, fluid compatibility and end standard are checked against the project piping specification, and spare seat or wedge parts are noted for the branches that see the most cycles. The listed size range and pressure band set the limits the body is built to.
Spare seat parts are stocked for the most cycled branches.
Hot Tags: Stainless Steel Rising Stem Gate Valve, China Stainless Steel Rising Stem Gate Valve manufacturers, flanged gate valve, flexible wedge gate valve, full bore gate valve, mechanical gate valve, mining gate valve, Worm Gear Gate Valve
You Might Also Like
Send Inquiry














