Stainless Steel Check Valve Flanged Ends
Lead time near 15 days, MOQ 100 pieces. FOB price from US $14.49 per piece.
Stainless Steel Check Valve Flanged Ends
Discharge points on subsea pipeline laterals
Crews locate this check valve at subsea and industrial pipeline discharge; its job is to let the line flow one way and shut the door the moment pressure tries to come back. Access and straight-run space decide where the check lands on the skid or main, since a disc needs room to lift and a seat needs room to be inspected later. The bore follows calculated flow, and the rating is checked against the highest pressure reached during start-up, trip and shut-down rather than the steady running figure. The setting follows the project drawing.
The table below carries the listed size band and working rating recorded for this valve listing.

Body material for submerged pipeline duty
Housing metal on this entry is Cast Iron / Stainless Steel; it carries internal pressure, stem or hinge loads and the occasional wetting from the surrounding line. The soft seat or metal seat contacts the fluid, and the closure follows the one-way wafer body fitted at the discharge point noted on the listing. Seat and body are selected together, since the fluid that wears the insert can also attack the shell. Stainless, carbon or cast bodies differ mainly in corrosion resistance and weldability; a stainless body tolerates wet service and mild chemical contact, while a carbon or cast iron body suits water, air and hydrocarbon duty where external coating can be maintained. Seat inserts are the first wear item, and buyers keep a spare seal for the busiest sizes rather than stocking whole spare valves. The hinge or guide surfaces are checked when the disc starts to rattle, since grit trapped between disc and seat accelerates wear on both. The body metal is matched to the most aggressive fluid expected on the run rather than the cleanest sample, because wetted surfaces see pumped product continuously while the shell only meets ambient moisture and occasional spray during access.
End patterns that mate to subsea flange or wafer runs
The end connection listed is Flanged, Wafer. A wafer pattern clamps between two mating flanges on the line, held by the flange bolts that pass through the body ears, so the valve itself carries no separate flange ring.
| Field | Figure |
|---|---|
| Listed service sector for the valve | Subsea Pipeline |
| Approval reference on the entry | ANSI |
| Nominal bore range covered | DN50–DN200 |
| Construction metal of the housing | Cast Iron / Stainless Steel |
| Pressure class the body carries | Pn10, Pn16 |
| Catalog class shown for the piece | Check Valve |
| How the ends join the line | Flanged, Wafer |
| Drawing number carried by the piece | DN50–DN200 |
| Product family in the catalog | Wafer Check Valve |
Disc closure against external hydrostatic head
Under forward flow the disc lifts off its seat and the bore opens; flow pressure holds it open while the line runs. When the pump trips, pressure eases off or the downstream side pushes back, the disc returns against the seat and blocks reverse movement. When the check chatters after long service, crews clean the sealing face, check the guide for grit and turn over the insert before condemning the body. A worn pin or guide face is the usual cause of a rattle, and these parts renew far cheaper than a housing replacement. The pressure class on the listing is chosen against peak surge, so a class picked on average pressure may weep when reversal arrives. Over repeated cycles the hinge surfaces and guide faces take the brunt of the movement, and these parts show wear before the housing does, so a rattle or chatter should be traced to pin, guide or seat before any decision to replace the casting. The spare matches the installed main.
Spare parts follow the wear pattern on these valves. The hinge pin, guide faces and seat insert are replaced before the housing shows any sign of wear, and a spare seal for the most cycled size usually sits beside the replacement disc in the maintenance store. When the check chatters after long service, crews clean the sealing face, check the guide for trapped grit and turn over the insert before condemning the body. These inspections take less time than pulling a whole valve off the line, and they keep the closure dependable through repeated start-up and shut-down cycles.
The metal sees internal fluid continuously and ambient moisture only around the flange and bonnet, so corrosion attention follows the wetted parts first. Coating, wrapping and external paint follow the plant's own corrosion practice once the piece enters the line, and the casting itself keeps service after the sealing parts are renewed. Inspect the exterior at each visit.
On site the valve is set in place with the correct flange bolts or weld bevel, and the closure is cycled once from fully closed to fully open to confirm the stem, disc or wedge moves without binding. Grit on the seat face is cleared before pressure is applied, and the joint is centered so the seal compresses evenly around the bore. A slow leak after the first test points to the seat rather than the shell, which is where maintenance attention usually starts.
A slow seat leak shows up on the first pressure test more often than a body failure, so maintenance attention goes to the insert, the hinge or guide surfaces and the sealing face before the casting itself is questioned.
Pipeline spares grouped by bore and pressure class
The listed bore band is DN50–DN200 and the pressure band is Pn10, Pn16; bore, end form, seat and class are checked against the piping drawing before commitment. The listing records ANSI as the standard reference. The first order may run to a single piece where permitted; pricing and lead schedule follow the quotation once size, end form and count are agreed.
Hot Tags: Stainless Steel Check Valve Flanged Ends, China Stainless Steel Check Valve Flanged Ends manufacturers, axial check valve, high durability valve, high pressure check valve, inline flow check device, low pressure check valve, Socket Weld Check Valve
You Might Also Like
Send Inquiry














