Turbine Operated Wafer Butterfly Valve
video

Turbine Operated Wafer Butterfly Valve

Turbine-operated grooved wafer butterfly valves, single-eccentric sealing, soft or metal seat. Pn10/Pn16, -30 to 400 C, casting body, used on chemical process lines.
Custom sizes are accepted and OEM is welcome. FOB price runs from US $11-880 per piece, MOQ 5 pieces.
Send Inquiry
Product Introduction

Turbine Operated Wafer Butterfly Valve

Turbine gear operation on chemical headers

This wafer butterfly valve sits on chemical process headers and larger line isolation points, where flow has to be opened, shut off or held against reverse movement without interrupting the rest of the plant. The listing covers process and utility lines where handwheel torque through a gearbox is preferred, and the body is sized to match the line diameter, pressure band and fluid type recorded on the source specification. Crews check the end type against the spool drawing first. On paper the rating is one number; on the rack it means flange spacing, bolt length and enough room for the actuator once the line carries working pressure and the surrounding pipework is fixed in place. The body and seal follow the listed service rather than a generic default. The isolation point keeps a clear shut-off when the line is opened for maintenance, and the spare for this branch is logged by size, seat type and end form so the right piece reaches the right pump room, rack or trench on the next maintenance visit. Field crews identify the branch first, then the valve.

Spare sets follow the next maintenance order, tagged by branch.

Grooved wafer body on process pipework

The body is casting body listed for Pn10 and Pn16 across the covered size range. Inside, the sealing path uses single-eccentric sealing path with soft seat or metal seat for chemical duty, which determines how the disc or wedge meets the seat each time the valve closes. The listed temperature band and pressure class govern which body and seat combination suits the duty, and the source specification records the size range the listing covers. Soft seats give a tight shut-off on clean water and utility lines, while metal seats stand up to abrasive or higher-temperature service where a soft elastomer would wear faster and need earlier replacement. The stem, disc or wedge moves within the body cavity, and the seal faces are protected from grit and scale as long as the line is flushed before commissioning. Wear shows first at the seat edge after repeated cycles, so spare seat parts are often stocked alongside the spare valve for the branches that see the most isolation work. The listed size range and pressure band are read from the source table before any spare is cut for the branch. Seat condition is checked during routine inspections.

Turbine operated grooved
Turbine-gear wafer butterfly valve fitted on a chemical process header.

Single-eccentric sealing path

End connection on this wafer butterfly valve is grooved wafer body mounted on process pipework between companion flanges. Flanged ends mate to companion flanges with bolts sized to the pressure class, and the flange face type is checked against the line standard recorded on the listing. Wafer bodies drop between two flanges and rely on through bolts to hold the body in place, which keeps the installed length short but leaves less standalone support than a flanged body. Grooved or welded variants prepare the end for the pipe joining method the spool drawing calls for. Before tightening, the gasket or seat face is aligned square, and bolt torque is worked across opposite sides rather than around the flange in one pass, which avoids pinching one side of the joint and leaves the seal sitting evenly on its contact face. Mismatched end preparation is the most common reason a delivered valve has to be adapted on site, so the end form is confirmed against the line drawing at order time.

SectionNominal
End connectionWafer
Pressure ratingPn10, Pn16
Standard record-
Listed serviceIndustrial, Water Industrial, Household
Product categoryButterfly Valve
Valve familyButterfly Valve
Body castingCasting
Model reference-
Nominal size range-

Soft and metal seat options for chemical duty

The listed driving arrangement for this wafer butterfly valve is set out in the source record. turbine gear reducer turns the stem from a handwheel, easing operation on larger discs The stem transfers handwheel, lever or actuator motion to the wedge, disc or ball inside the body, and open and shut positions are read from the stem travel, handle angle or actuator pointer. Gear or turbine reducers reduce the torque needed on larger discs, while pneumatic actuators respond to an air signal from the control room or local panel. Manual levers usually carry detents that hold the chosen position, and rising stems make the wedge position visible above the bonnet without opening the cover. Actuator air supply, stroke length and signal type are matched to the line control scheme before commissioning. The stem seal and packing are checked at the same inspection that verifies the position marks. On branches operated infrequently, crews exercise the valve during routine inspections to keep the seat free of deposits that would otherwise bind on the next closure.

Handwheel torque and stem travel notes

The source listing records pressure rating, size range, standard record and listed service in the table below, along with the model reference and product category copied from the source record. A trial order can start with a single piece; the price bracket and delivery window go with the quotation, and custom details are handled per inquiry when the line dimensions fall outside a standard stock range. Pressure class, fluid service and connection standard are confirmed against the project drawing before the order is cut. This wafer butterfly valve is sized from the recorded specification rather than an assumed rating, and spare seat or wedge parts are noted for the branches that see the most cycles during the plant year. The specification sheet and the listing read from the same record.

End form and flange face are checked against the spool list.

Hot Tags: Turbine Operated Wafer Butterfly Valve, China Turbine Operated Wafer Butterfly Valve manufacturers, butterfly valve, chemical butterfly valve, ductile iron industrial Anti corrosion butterfly valve, Flanged Cast Iron PN10 Butterfly Valve, high pressure butterfly valve, irrigation butterfly valve

Send Inquiry

whatsapp

Phone

E-mail

Inquiry