Flanged Single Sphere Rubber Pipe Joint
video

Flanged Single Sphere Rubber Pipe Joint

Flanged single sphere rubber expansion joint (model RFJ-004) with an EPDM rubber body and carbon steel flanges. It covers DN15 to DN4000 and working pressures from Pn6 to Pn25.
It absorbs axial extension and compression with lateral movement of +/-5 to 20 mm. Certified to CE, ISO14001, JIS and ISO9001, with a 12 month warranty and FOB price from US $24 per piece.
Send Inquiry
Product Introduction

Flanged Single Sphere Rubber Pipe Joint

Vibration from a running pump travels straight into the pipework unless something in the line absorbs it first. This RFJ-004 flanged single sphere rubber joint sits between the pump nozzle and the discharge header, where an EPDM body carries the fluid while carbon steel flanges bolt the assembly to the mating pipework. The sphere flexes under axial extension, axial compression and lateral offset, so thermal growth and pump shake do not stack up against the pump casing or the first fixed support on the run. Size coverage runs DN15 to DN4000, and pressure classes cover Pn6, Pn10, Pn16 and Pn25 across drainage and utility service. The certification listed on the source record reads CE, ISO14001, JIS and ISO9001. A trial order can start at five pieces; the bracket sits in the source listing, and the delivery window follows the quantity booked.

Sitting between a pump nozzle and the discharge header

Pump connections are where this piece earns its place on the spool list. The joint mounts directly against the pump outlet flange, taking the residual vibration that the flexible mounting under the pump frame cannot remove, and it separates the pump nozzle from rigid pipework so a small thermal movement does not pull on the casing bolts. Drainage mains, basement sump lines and plant circulation loops all show the same pattern: a centrifugal pump, a short straight spool, then the compensator before the run reaches a wall or a fixed hanger. Crews on site usually ask whether the unit can handle lateral drift as well as push and pull; the listed movement window covers axial extension, compression and lateral offset within ±5 to 20 mm depending on size and pressure class. Where the discharge line rises through several floor slabs, the compensator also quietens the noise that otherwise radiates up the rigid steel run. On a wet pit installation, access below the joint matters more than the drawing suggests: the flange bolts have to be reachable from the pit floor, and the joint should not be buried where the cover cannot be lifted for later inspection.

Pump nozzle loads stay low when the joint takes the movement first.

How the EPDM sphere takes axial and lateral movement

The sphere body is the flexible element of the assembly. EPDM rubber moulds into a single bell-like chamber between the two flange necks, and the rubber stretches, compresses or leans sideways as the line moves, instead of transferring that motion as a bending force into the adjacent pipe. Axial extension pulls the sphere longer, axial compression pushes it shorter, and lateral movement shifts one end sideways relative to the other; each direction flexes the same body without a sliding seal or a metal slip that can seize up. The rubber composition suits the drainage and utility water service listed on the record, and the compound should be checked against any special chemical dosing in the line before order confirmation. Burst figures referenced in the overview sit above 30 bar, well clear of the listed working classes, though the working rating still governs selection rather than the burst number. Flanges on this version are carbon steel, drilled to match the companion flange pattern selected for the line, and the gasket between joint and mating face follows the same drilling.

PartDetail
Model referenceRFJ-004
Certification recordCE, ISO14001, JIS, ISO9001
Product familyRubber Expansion Joint
End connection formFlanged
Stated serviceDrainage
Nominal size rangeDN15~DN4000
Body and seal materialCarbon Steel, EPDM Rubber
Listed product categoryRubber Expansion Joint
Listed pressure classesPn6 / Pn10 / Pn16 / Pn25

Flange drilling and gasket practice on drainage runs

Installation follows ordinary flange practice. The two end flanges land square on the mating faces, bolts go through opposite pairs in diagonal sequence, and torque comes up evenly so the gasket beds without one side crushing before the other. Avoid pulling the joint into alignment by forcing one flange over; the sphere should be centered, and any angular misfit corrected at the adjacent spool rather than levered into the rubber body. Gaskets sit between steel flange faces, and the bore should match the pipe internal diameter so flow does not catch on a gasket lip. Drainage water can carry small grit, so the flange faces are wiped clean before the joint is closed, and thread protectors stay on until the spool is ready to be lifted into place. Where the line carries occasional wastewater with dosing chemicals, the EPDM compound is checked against the dosing record before the unit leaves the workshop. Clean faces seal cleanly.

RFJ-004 flanged single sphere EPDM rubber pipe joint with carbon steel flanges
Single sphere EPDM compensator bolted between carbon steel end flanges.

Sizing from DN15 up to the widest headers

Size selection starts with the line diameter. The listing covers DN15 through DN4000, spanning small utility taps and large trunk mains, and the pressure class is chosen against the line rating among Pn6, Pn10, Pn16 and Pn25. Large diameters in particular need checking against support spacing: a wide compensator carries its own weight plus the line water, and nearby hangers or saddles carry that load so the rubber sphere is not left hanging under the flange. The model reference on the source record is RFJ-004, product type Rubber Expansion Joint, and the listed usage field reads Drainage. Before dispatch, workshop staff confirm flange dimensions and bore, check the rubber body for moulding faults, and pack the unit so the sphere does not get crushed against a flange edge during transit.

Hot Tags: Flanged Single Sphere Rubber Pipe Joint, China Flanged Single Sphere Rubber Pipe Joint manufacturers, carbon steel joint, fabric reinforced rubber joint, fluid joint connection, industrial pipe connector, pipeline connection joint, stainless steel joint

Send Inquiry

whatsapp

Phone

E-mail

Inquiry