Ductile Iron Grooved Flange Adaptor
ISO, CE, UL, FM and CCC certified. FOB pricing runs US $10-12 per piece, minimum order 100 pieces.
Ductile Iron Grooved Flange Adaptor
This grooved flange adaptor bridges a grooved fire main onto flanged pump, valve or equipment connections in industrial yards. The ductile iron body carries an EPDM gasket, covering DN25 to DN300 at 1.6MPa, and the listed certification record reads ISO, CE, UL, FM and CCC. Most units end up where a grooved riser has to mate with a flanged piece of fire protection equipment. The bracket runs USD $10 to $12 per piece, with a hundred-piece minimum order, and the listing leaves the delivery window open for scheduling at booking.
Jumping from a grooved main onto flanged fire equipment
Fire protection layouts mix grooved pipe and flanged equipment more often than a drawing suggests. Grooved mains run along rack rooms, risers and branch lines, while pumps, control valves, monitors and manifold pieces arrive with flanged ends. The adaptor sits at that transition: the grooved side clips onto the pipe end, the flanged side bolts to the mating equipment flange, and the EPDM gasket seals the joint. Fire contractors call for this piece when a grooved riser has to connect to a flanged pump inlet or a valve body, and the adaptor removes the need to weld a companion spool on site. On a yard hydrant or monitor branch, the same transition appears where the underground main meets above-ground equipment. The fit-up checks that matter here are the groove profile on the pipe end, the gasket seating inside the adaptor, and the bolt pattern against the equipment flange. Crews on site usually confirm the mating flange class before lifting the adaptor into place, because a drilling mismatch stalls the connection until the next spare arrives. Check the drilling before lifting.
The transition removes a welded companion spool, and no hot work is needed on site.
Ductile iron body with the EPDM sealing gasket
The adaptor body is cast in ductile iron, the material listed on the source record. Ductile iron gives the casting enough toughness for fire service handling and outdoor exposure, while the EPDM gasket supplies the sealing face between adaptor and mating flange. The gasket compresses under the flange bolts, closing the face-to-face gap so water does not weep at the joint under pressure. The listing carries model reference XGQT, and the product type field reads Flange Adaptor. On installation, the gasket sits square in its groove, the adaptor is centered on the flange face, and bolts come up in diagonal sequence rather than one side at a time. The body should be checked for casting flashes or sand in the bore before it goes on the line, because a trapped grit particle will score the gasket on the first pressure cycle. The ductile iron casting also takes the impact of yard handling and the occasional knock from a hose cart without cracking the way a brittle cast body might. Gasket square, adaptor centered.
| Fitting | Rating |
|---|---|
| Model reference | XGQT |
| Certification record | ISO, CE, UL, FM, CCC |
| Product family | Flange Adaptor |
| End connection form | Flanged (grooved adaptor) |
| Stated service | Fire protection pipeline |
| Nominal size range | DN25 to DN300 |
| Body and seal material | Ductile Iron |
| Listed product category | Flange Adaptor |
| Listed pressure classes | 1.6MPa |
Grooved adaptor face against the mating flange
The grooved side and the flanged side do different jobs. The grooved end clips onto the prepared pipe end, held by the coupling groove and gasket that lock the adaptor to the main, while the flanged end carries bolt holes drilled to mate with the companion flange on the equipment. The two faces meet at the adaptor shoulder, and the transition between groove pattern and flange drilling is built into the casting rather than assembled on site. When the mating flange arrives with a different drilling, that mismatch shows up before bolting begins, so the adaptor should be checked against the equipment drawing rather than assumed standard. Fire protection pipeline is the stated use field on the record, and the 1.6MPa rating aligns with common fire main pressure classes. Groove first, flange second. On grooved mains the coupling gasket and housing are fitted after the adaptor seats on the pipe end, and the housing bolts are torqued to the groove pattern before the line is pressurized.

Sizes and pressure rating on fire protection pipelines
Size coverage runs DN25 to DN300, from small branch taps to large riser connections. The pressure rating listed on the record is 1.6MPa, which sets the working class the adaptor carries in fire protection service. Before dispatch, workshop staff verify the groove profile, check flange hole spacing and bore, confirm the EPDM gasket is fitted, and inspect the casting surface against the order. Bulk packing follows the fire project delivery schedule, and the open delivery field on the listing means timing is agreed when the order quantity is confirmed. Where the installation runs outdoors, the body finish and any external protection are checked against the yard's corrosion practice. Fire pump inlets, monitor branches and valve manifold connections all draw from this size range, and the adaptor is matched to the equipment flange rather than the grooved pipe alone. Sizes follow the riser and branch. On a fire yard where grooved mains feed flanged hydrant valves and pump connections, the adaptor lets the contractor keep the grooved pipe system standard while still mating to equipment that arrives with bolted flanges, avoiding a custom welded spool for every transition point on the layout.
Hot Tags: Ductile Iron Grooved Flange Adaptor, China Ductile Iron Grooved Flange Adaptor manufacturers, ANSI Anti corrosion Carbon steel flange, Blind Cast Iron ANSI Flange, flange bolt assembly set, flange installation kit, flange sealing hardware, Plate Flat Welding Flange
You Might Also Like
Send Inquiry














